Cyber Services / All lessons / Diploma in Network Technology / Basic CLI Configuration

Basic CLI Configuration

Module 12 of 36 · 3 min read · Free to read

MODULES ↓ Command blocks have a COPY button

Your Gateway to a Career in Network Engineering

Basic Router/Switch Configuration via CLI

Welcome to the Command Line Interface (CLI). While graphical user interfaces (GUIs) are user-friendly, the CLI is the preferred tool for network professionals. It is faster, more powerful, scriptable, and provides granular control over every aspect of a network device. This guide will walk you through your first interaction with a router or switch CLI.

Accessing the CLI

There are three primary ways to access a device's CLI:

  • Console: A direct physical connection using a special console cable (usually a light-blue rollover cable). This is required for the initial setup of a new device.
  • SSH (Secure Shell): A secure, encrypted method to access the CLI remotely over the network. This is the preferred method for daily management.
  • Telnet: An older, insecure method for remote access. Telnet sends all data, including passwords, in plain text and should be avoided.

Navigating the CLI Modes

The Cisco IOS CLI has a hierarchical structure with different "modes." Think of it like a secure building: you start in the lobby, then pass through security to gain more access, and finally enter specific offices to make changes.

Mode NamePromptPurposeHow to Enter
User EXEC ModeRouter>(Lobby) Basic monitoring. You can look but not touch. Used for simple show commands.Default mode after connecting.
Privileged EXEC ModeRouter#(Security Desk) Full monitoring and access. Allows all show commands, debugging, and file management.From User mode, type enable.
Global Configuration ModeRouter(config)#(Manager's Office) Make changes that affect the entire device.From Privileged mode, type configure terminal.
Specific Configuration ModeRouter(config-if)#(Specific Department) Make changes to a specific feature, like an interface or a protocol.From Global Config mode (e.g., interface g0/0/0).

To move back one level, type exit. To go all the way back to Privileged EXEC mode from any sub-configuration mode, type end or press Ctrl+Z.

Essential First-Step Configurations

These are the five commands you should run on almost any new device. All are done from Global Configuration Mode.

Switch> enable
Switch# configure terminal
Switch(config)# hostname MCA-SW-01
MCA-SW-01(config)# enable secret your-secure-password
MCA-SW-01(config)# line console 0
MCA-SW-01(config-line)# password your-console-password
MCA-SW-01(config-line)# login
MCA-SW-01(config-line)# exit
MCA-SW-01(config)# line vty 0 15
MCA-SW-01(config-line)# password your-remote-password
MCA-SW-01(config-line)# login
MCA-SW-01(config-line)# exit
MCA-SW-01(config)# banner motd # Unauthorized Access is Prohibited! #
MCA-SW-01(config)# end
MCA-SW-01#

Interface Configuration: Making the Device Useful

Now let's configure an interface. The commands differ slightly based on whether it's a router (Layer 3) or a switch (Layer 2).

Router Interface (Layer 3)

The goal is to assign an IP address to make the router participate in a network.

Router# configure terminal
Router(config)# interface GigabitEthernet0/0/0
Router(config-if)# description Link to Main LAN
Router(config-if)# ip address 192.168.1.1 255.255.255.0
Router(config-if)# no shutdown
Router(config-if)# end
By default, all router interfaces are administratively disabled. The no shutdown command is essential to activate the interface.
Switch Interface (Layer 2)

The goal is to configure the port for a user device and assign it to a VLAN.

Switch# configure terminal
Switch(config)# interface GigabitEthernet0/1
Switch(config-if)# description Connection to User PC
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 10
Switch(config-if)# no shutdown
Switch(config-if)# end

The Most Important Command: The Question Mark `?`

The CLI has built-in, context-sensitive help. Typing ? will show you all available commands in the current mode or all possible options to complete a command you've started.

  • show ? - Shows all commands that start with "show".
  • show ip ? - Shows all options for the "show ip" command.
  • sh? (no space) - Shows commands starting with "sh".

Saving Your Configuration

Changes made in configuration mode are applied immediately to the **running-config** (the configuration currently active in RAM). However, this configuration will be lost if the device reboots. To save your changes permanently, you must copy them to the **startup-config** (the configuration stored in NVRAM).

MCA-SW-01# copy running-config startup-config
Destination filename [startup-config]?  [Press Enter]
Building configuration...
[OK]
MCA-SW-01#
The shorthand for this command is copy run start. Forgetting to save is the most common mistake beginners make!
Modules (36) ← Diploma in Network Technology